Home   About Contact Order Downloads Employment Opportunities
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The information contained herein

is for reference only.  For the most accurate drawings and specifications

please contact our Sales  or Engineering team.

Thank you.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The information contained herein

is for reference only.  For the most accurate drawings and specifications

please contact our Sales  or Engineering team.

Thank you.

 

 

 

 

 

 

 

 

 

 

 

The information contained herein

is for reference only.  For the most accurate drawings and specifications

please contact our Sales  or Engineering team.

Thank you.

 Punture Bar

Puncture Device Product Listing

Our devices are categorized into Mountable (with bracket) or Non-mounted,
Puncture Devices for Non-threaded Cylinders
and Accessories.
Please contact us if you need more information or would like to
speak directly with one of our engineers
. You may also order directly from our site.

Puncture Device for threaded disposable cartridges
Leland’s Original High Pressure Puncture Device provides for safe puncturing of threaded disposable gas filled cylinders.

  • Two female outlets are stocked, 1/8 NPT or .305 tire valve stem
  • Three female thread sizes for the puncture inlet; 3/8-24UNF, 1⁄2-20UNF, 5/8-18UNF
  • Hardened stainless puncture pin for repeatability
  • Sintered screen filter behind pin prevents particulate contamination >20 Microns
  • Mountable with a bracket and 1-12UN nut
Specifications
  • Two female outlets are stocked, 1/8 NPT or .305 tire valve stem
  • 416 Stainless Steel
  • Inlet Pressure (max) 206 Bar, 3000 psi
  • Inlet Pressure (max) 206 Bar, 3000 psi
  • Sintered Screen Micro Port Filter installed behind puncture pin

ORDER MOUNTABLE OR NON MOUNTABLE

CROSS SECTION VIEW

DETAIL VIEW

WARNING: These devices are NOT intended to be connected to refillable PAINTBALL cylinders. If you need such a device, please contact us so that we can help us obtain the correct item. These devices DO NOT control pressure from the gas cylinder, the purchaser of the equipment assumes all responsibility for the resulting effect of high pressure after the outlet of our devices.

(Click on photos below to enlarge or see multiple views)
Mountable Puncture Device  (bracket and nut sold separately)
Puncture Device Mountable 65026 SetGENERAL DESCRIPTION: High strength mounting for all sized threaded disposable cylinders. The 65026 series mountable puncture devices accept 3/8”-24UNF, 1⁄2”-20UNF and 5/8”-18UNF threaded neck cylinders. The puncture pin and seal are designed to cleanly puncture the cylinder without initial gas loss. There is a primary gas relief hole near the seal so that removing a cylinder with gas remaining is immediately obvious by the loud hissing noise.

Select a 1/8”NPT outlet and connect it to virtually anything. This device is only intended to safely puncture a disposable gas filled cylinder; it is incumbent upon the user to properly control the gas pressure coming out of the cylinder. If you need to reduce the gas pressure from one of our cylinders, please go to our REGULATOR section as these also have the capability to puncture and seal. For bracket and retaining nut please scroll down.

Item #
View
Cylinder Inlet Thread
Outlet Port
65026-18Y58
5/8”-18UNF
1/8" NPT
65026-305Y58
5/8”-18UNF
.305 Tire
65026-18Y12
1/2"-20UNF
1/8" NPT
65026-305Y12
1/2"-20UNF
.305 Tire
65026-18Y38*
3/8”-24UNF*
 
*requires P/N 50037 bushing
1/8" NPT
65026-305Y38*
3/8”-24UNF*
 
*requires P/N 50037 bushing
.305 Tire

(Click on photos below to enlarge or see multiple views)
Non-mounted Puncture Device
GENERAL DESCRIPTION: High strength mounting for all sized threaded disposable cylinders. The 65026 series non-mountable puncture devices accept 3/8”-24UNF, 1⁄2”-20UNF and 5/8”-18UNF threaded neck cylinders. The puncture pin and seal are designed to cleanly puncture the cylinder without initial gas loss. There is a primary gas relief hole near the seal so that removing a cylinder with gas remaining is immediately obvious by the loud hissing noise.

Select a 1/8”NPT outlet and connect it to virtually anything. This device is only intended to safely puncture a disposable gas filled cylinder; it is incumbent upon the user to properly control the gas pressure coming out of the cylinder. If you need to reduce the gas pressure from one of our cylinders, please go to our REGULATOR section as these also have the capability to puncture and seal.

Item #
View
Cylinder Inlet Thread
Outlet Port
65026-18N58
5/8”-18UNF
1/8" NPT
65026-305N58
5/8”-18UNF
.305 Tire
65026-305N12
1/2"-20UNF
.305 Tire
65026-18N12
1/2"-20UNF
1/8" NPT
65026-305N38*
3/8”-24UNF*
 
*requires P/N 50037 bushing
.305 Tire
65026-18N38*
3/8”-24UNF*
 
*requires P/N 50037 bushing
1/8" NPT

(Click on photos below to enlarge or see multiple views)

Puncture Devices for Non-threaded Cylinders
Solid Brass and Stainless Steel construction to accept all 10cc non-threaded cylinders. Used widely to clear heating oil lines in the Northeast and A/C condensate drain lines everywhere else.
Item #
Outlet Port
Description
51008
1⁄4” NPT
51008 Any non threaded 8g CO2 or N20 cartridge can be punctured by placing it in the screw-on holder and turning down onto the hex puncture block. 1⁄4” NPT female outlet with an anti-blowback check valve is built in. Solid brass construction with a heat treated puncture pin makes this a classic tool used for clearing oil lines, A/C drains and many more applications.
WARNING: This device DOES NOT control pressure from the gas cylinder, the purchaser of the equipment assumes all responsibility for the resulting effect of high pressure after the outlet of our device.

(Click on photos below to enlarge or see multiple views)

Accessories
Item #
Item Name
Description
65027
Bracket
65027 Mounting bracket for 65026 series puncture devices which have the mounting option. 18-8 Stainless heavy gauge designed with proper offset to allow our larger 2.40” diameter cylinders. Don’t forget to order the correct nut, P/N 65028.
65028
Nut
65028 Big 1-12 Nut,18-8 Stainless, to secure a mountable 65026 series puncture device to a 65027 bracket.

Back to Top

Punture Bar

 

 Rev 17.0
 
 
Copyright 2014 All rights reserved.    The Leland logo is a registered trademark of Leland Limited Incorporated.